Fibaro Sensore di acqua e fluidi Z-Wave Plus

59,29

Prezzo IVA esclusa: € 49,00

Disponibilità:
In magazzino
Codice Prodotto:
ES-17-FIB_FGFS-101ZW5
Marca:
Fibaro

Non ancora valutato
Scrivi una recensione

Descrizione

With a futuristic design and compact size, this flood Fibaro sensor alerts you in a threatening flood, or an increase or a rapid drop in temperature . It very well find failement place in your home to protect the safety of the whole family . This flood Fibaro detector is a universal flood and temperature , Z -Wave compliant. It can be powered by battery or an external power supply 12 or 24 VDC . When connected to an external power source , the battery is a source of backup power. The flood alarm is sent to the device Z -Wave network or any wired alarm system which , through its NC dry contacts output .

The device includes a temperature sensor, for example by monitoring the temperature of the soil. It also has an LED and an audible alarm . In addition, the sensor is equipped with a tilt sensor for movement up or tilt the camera to the main controller , for example, when someone took the sensor from its original location. The LED indicates a flood, the mode or the communication range of the Z -Wave network.

This flood Fibaro sensor is waterproof, and drift to the surface of the water, continuing to send the alarm signal in the event of major flood water . It is designed to be placed on the ground , but it can also be installed on a wall using a wire probe.

For your safety, and to ensure that the flood detector is working properly , it was equipped with a tester range of Z -Wave network. Communication in wireless mesh network Z -Wave wireless allows you to stay connected with the controller over a long distance through indirect connectivity with other Z -Wave modules. The integrated LED allow you to easily check if the sensor has a good range and can communicate with the system Fibaro or requires a different location. A Z -Wave controller ( remote dongle ... ) is necessary to integrate this module in your network if you already have an existing network.

FEATURES :

  • Flood detector temperature and Z -Wave
  • Can be connected to any alarm system ( terminal floating output )
  • Can be installed anywhere - contacts flood sensors can be extended with a wire
  • Powered by a battery or external DC power supply
  • Protection against theft - the inclination is shown on the Z -Wave network or system alarm main controller
  • Two modes - flood / temperature sensor or just a temperature sensor
  • Tester coverage Z -Wave network integrated
  • Update the wireless box Fibaro Home Center 2
  • Simple installation - just put on a flood-prone area

SPECIFICATIONS :

  • Module Type : Z -Wave Transmitter
  • Power supply: 12 to 24 VDC
  • Battery Type: CR123A
  • Battery life : 2 years
  • External power consumption : 0.4 W
  • Maximum current supported output (ALARM NC, NC TAMP ) : 25mA
  • Maximum rated voltage output : 40V (AC or DC)
  • Frequency: 868.42 MHz
  • Transmission distance: 50m free field, 30 m indoors
  • Dimensions: 72 x 28 mm (diameter x height)
  • Temperature : 0-40 ° C (-20 ° C to 70 ° C if external power supply)
  • Measuring range of temperature: -20 to 100 ° C
  • Measurement accuracy : 0.5 ° C ( in a range from 0 to 40 ° C)
  • Standards : EMC 2004/108/EC and R & TTE 199/5/WE

Fibaro Water Flood Sensor Manual:

Unboxing:

 

Specifiche

Control principale compatibilità
eeDomus+ full compatible
Fibaro Home Center 2 v4.160 full compatible
Fibaro Home Center Lite v.4.160 full compatible
Vera Edge / Plus Full Compatible
Zipabox/Zipamini/ZipaTile full compatible
Piper / Piper NV (v.1.7.1) not tested
Indigo Compatible (Testing)
jeedom full compatible
Domoticz full compatible
ZiHome full compatible
Vera 3 full compatible
Vera Lite full compatible
Tech Data
IP Rating -
FLiRS No
Power Supply Battery 1 x CR123A or 12 V DC
Explorer Frames - NWI Support Yes
SDK 6.51.06
App Version 3.2
Device Type Slave with routing capabilities
Z-Wave Alliance Product Link http://products.z-wavealliance.org/products/1354
Generic Device Class Alarm Sensor
Specific Device Class Routing Alarm Sensor
Routing No
Procedures
Inclusion 1) Open the cover by turning it counter-clockwise. 2) Remove battery blocker. 3) Locate the sensor nearby the main Z-Wave controller. 4) Set the main Z-Wave controller into learning mode (see main controller’s operating manual). 5) Quickly, triple click the TMP button located inside the casing. 6) Wait for the device to be included into the system. Successful inclusion will be confirmed by the controller. 7) Close the cover by turning it clockwise. 8) Place the sensor onto a surface prone to flooding. Three electrodes underneath the device should evenly touch the surface.
Exclusion 1) Open the cover by turning it counter-clockwise. 2) Make sure the sensor is connected to a battery or a DC power supply. 3) Locate the sensor nearby the main Z-Wave controller. 4) Set the main Z-Wave controller into learning mode (see main controller’s operating manual). 5) Quickly, triple click the TMP button located inside the casing. 6) Wait for the device to be excluded from the system. Successful exclusion will be confirmed by the controller.
Factory Reset 1) Open the cover by turning it counter-clockwise. 2) Make sure the sensor is connected to a battery or a DC power supply. 3) Press and hold the TMP button for 15-20 seconds until LED glows yellow to confirm entering into 4th menu option. 4) Release and click the TMP button to start reset procedure. 5) The LED glowing red and then turning off will confirm successful reset. Reset completion will be also confirmed by an acoustic signal. Note! Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable.
Wake Up FIBARO Flood Sensor will wake up at a defined time interval and will ALWAYS try to communicate with the main controller. There is a possibility to wake up the device manually by clicking the TMP button.

Recensioni (0)

Scrivi una recensione

Nota: Il codice HTML non è tradotto!

Negativo            Positivo


Continua

Z-Wave Italia

Il negozio online che vende attrezzature di automazione domestica Z-Wave radio. Z-Wave è lo standard internazionale per le reti wireless dei sistemi di controllo nella vostra casa. È possibile gestire l'illuminazione, elettricità, persiane, gli allarmi e altro ancora. I prodotti Z-Wave di fornitori diversi lavorano bene insieme, permettendo il controllo della casa intelligente.

Contattaci

Phone:
+393404556393
E-mail:
info@zwaveit.com
Skype:
palumbrogabriele

Twitter

Facebook